▲
 
Diamond Tool and Abrasives, Inc.
There Is No Substitute For Experience

What is Fine Grinding?

  • Fine Grinding is a batch-mode abrasive machining process that combines the speed and aggressiveness of super abrasive wheels with accuracy of lapping kinematics to produce flat and parallel work piece surfaces.
  • The cutting tool consists of an upper and lower wheel composed of diamond or cubic boron nitride (CBN) with different bond types (vitrified bond, resin bond or metal bond) and act as the support plates for the work pieces.
  • The machine tool has evolved from the vertical double-wheel lapping machine design with a planetary work drive system, also known as lapping kinematics.
  • In place of lapping wheels, grinding wheels are fitted and cooled through labyrinth in the working wheels and a coolant fed through holes in the upper wheel.
  • Since Fine Grinding requires higher forces and uses higher cutting speeds, motors, gears and the rigidity of the machines are much stronger than lapping machines.
  • Work pieces are guided between the upper and lower working wheel in an epicyclical path as defined by inner and outer pin ring, upper and lower working wheel, speeds and directions, while material removal takes place simultaneously on both sides.

Why use Fine Grinding?

General

  • Accuracy results, previously only achieved by lapping
  • The pellet structure allows a layout of the grinding medium, corresponding to the kinematics conditions
  • Long and constant process cycles without dressing processes
  • The space between the pellets allows a high flow rate of the coolant
  • Very good chip flow without temperature problems
  • High process quality, consistent repeatability of achieved values
  • Also large surface work pieces can be machined
  • Batch processing
  • Work pieces are loosely held in carriers and therefore machined stress free (without distortion - especially for machining of thin or delicate parts)
  • Work pieces of different shapes could be machined (i.e. round, rectangular or irregular; full surface or with cut-outs)
  • Easily to be automated

Fast

  • High removal rate using super abrasive diamond and CBN (3 - 20 times faster than lapping)
  • Possible saving of pre-machining steps
  • Long intervals between resharpening
  • High flexibility
  • Automated solutions

Clean

  • Recycling of coolant
  • Tremendous less waste than with lapping
  • Minimal work piece cleaning necessary
  • Reduced downtime
  • Cleaning of work pieces without problems by rinsing; in comparison to lapping ultrasonic or chemical cleaning is not necessary

Economic

  • High removal rate (reduces capital costs and personnel expenditure)
  • Low wheel wear - long life time of the grinding wheels (reduces the tool costs)
  • Low waste disposal costs (reduces the current running costs)
  • Low work piece cleaning costs (reduces the current running costs)
  • Possible saving of additional machining steps
  • Easy wheel maintenance - low tool manufacturing costs by using a Standard-Pellet-Form.

Fine Grinding

  • Performed with super abrasive (diamond or cubic boron nitride - CBN) wheels
  • Stock removal caused by micro grooving / -cutting
  • Fine-ground surface has cross-hatched marks
  • Coolant is recycled
  • Fine-ground parts are coated only with a thin layer of coolant and therefore only minimal workpiece cleaning is necessary
  • Wheel speeds are typically 2 - 15 m/s
  • 3 - 20 times faster than lapping (removal rate)

Lapping

  • Lapping is a working process, during which workpiece and tool slide over one another on a loosely applied medium (lapping compound) and are subject to continually changing direction of rotation.
  • Stock removal caused by rolling and sliding action of abrasive grains
  • Lapped surface is dull and crater-like
  • Material and lapping compound are not recycled
  • Lapped parts are contaminated with lapping compound and require cleaning
  • Lapping speeds are generally limited to < 1 m/s

Definition of the Tooling Methods

  • Lapping (flat parts - single or double-side) is the abrasive machining process for removing material using a loose abrasive in a liquid mixture (known as a slurry) at low speeds.
  • Loose abrasive is moving over the surface under pressure (fig. 1), will knead, abrade, chip or scrape away the surface of the workpiece (fig. 2). By exceeding the bending strength the material breaks out.
  • Fine Grinding (flat parts - single or double-side) is the abrasive machining process for removing material using a bonded Superabrasive wheel at low speed with a liquid to keep the part cool. The fixed grain of a geometrically indefinable cutting shape acts like a plow (fig. 3) and material is removed by micro-grooving /-cutting (fig. 4). The chip formation occurs by exceeding the shearing strength.

Fine Grinding vs Lapping

Kinematics of the Fine Grinding Process

Fine Grinding generally follows the same kinematic principle as lapping. The workpieces are held in carriers which are driven to describe a planetary motion covering the full surface of the Fine Grinding wheel. The drive mechanism consists of an inner and outer pin ring. The outer ring is generally fixed while the inner ring rotates in either the opposing or the same direction as the lower working wheel to create a series of epicyclic rotations.

Inquiry Form

* Indicates A Required Field

I read and understood the privacy policy which can be found in the footer of this page.